Wolf 600 Series BI-48SD Guida di Installazione Pagina 26
- Pagina / 40
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Panel Installation 26
1
/8"
(3)
OVERLAY PANEL
SPACER PANEL
BACKER PANEL
TRIM
5
/16" (8) min
Panel assembly cross
section.
Panel assembly rear view.
1
/4" (6)
.10" (3)
OVERLAY
PANEL
SPACER
PANEL
BACKER
PANEL
3
/4"
(19)
typical
Overlay Panels
I
f your customer has chosen an overlay design applica-
tion, make sure that the panels you are about to install
match dimensions listed in the overlay panel specifica-
tions on pages 28–29. Additional panel design information
can be found in the Sub-Zero design guide and on our
website, subzero.com.
IMPORTANT NOTE: The size of the overlay panel is
critical. It must fit over the door frame. Also, do not
exceed the maximum per panel weight for your specific
model. Refer to the chart below.
Overlay models are shipped without handle hardware.
The cabinet manufacturer or designer will need to provide
handle hardware to match the overall decorating scheme.
To install overlay panels, first remove the door trim
molding. For side-by-side models and the upper door for
over-and-under models, insert a screwdriver tip into the
top corner slot on the handle side and pop out the trim
molding. Remove the screws and frame. For the drawer
on over-and-under models, insert a screwdriver tip into
the slot on either side of the trim molding running along
the top of the drawer and pop out the trim molding.
Remove the screws and frame. Refer to the illustrations
on page 23.
Sub-Zero allows a
1
/4" (6) space to slide the backing
material into place in the frame. If your material is thicker
than a
1
/4" (6), either rout an edge around the panel to get
a proper fit or mount the decorative overlay panel on a
sheet of
1
/4" (6) thick material and insert the backing
material into the channel.
Y
ou must allow for .10"
(3) s
pace between the backer
board and the decorative panel, so the panel will slide
easily into the door frame.
The illustrations below provide a cross section view of the
three-panel assembly, showing placement of the trim and
a rear view of the three-panel assembly with critical
dimensions, standard for all built-in models.
Install the handle hardware before inserting the panel. We
recommend larger D-style pulls. The use of small, one-
piece knobs is not recommended. If you use screws with
thick heads, you will need to countersink the screws into
the backer panel before sliding the assembly into place.
Slide the panel into the frame on the door. With the panel
in position, replace the frame end. Make sure the panel is
inserted completely into the channel for proper fit and
alignment.
To reinstall the trim molding on side-by-side models and
the upper door for over-and-under models, insert the top
of the trim molding into the grooves at the top of the door
and work downward, snapping the trim molding into the
clips on the frame.
For the drawer on over-and-under models, start at one
end and move towards the opposite end, snapping the
trim molding into the clips on the frame.
Overlay Panel Requirements
MAX WEIGHT PER PANEL
BI-36R, BI-36RG and BI-36F 75 lbs (34 kg)
All Other Overlay Models 50 lbs (23 kg)
Grille Panel 13 lbs (6 kg)
MIN PANEL THICKNESS
All Overlay Panels
5
/8" (16)
- Built-In Refrigeration 1
- Important Note 2
- Contents 2
- Built-In Refrigeration 3 3
- Before You Start 3
- Model Specifications 4 4
- Overall Dimensions 4
- Specifications 4
- Model Specifications 5 5
- Model Specifications 6 6
- Model Specifications 7 7
- Site Preparation 8 8
- Opening Dimensions 8
- Site Preparation 9 9
- Site Preparation 10 10
- Site Preparation 11 11
- Electrical Requirements 12
- Plumbing Requirements 13
- Site Preparation 14 14
- Anti-Tip Bracket Installation 14
- Wood floor. Concrete floor 15
- Unpack the Unit 16
- Grille Removal 16
- Built-In Installation 16 16
- Built-In Installation 17 17
- LEVELING LEG 18
- ADJUSTMENT 18
- Built-In Installation 19 19
- Door Adjustment 19
- Panel Installation 19
- ANCHORING 20
- WATER FILTER 21
- MAX WEIGHT PER PANEL 22
- MIN PANEL THICKNESS 22
- 4" (6) 22
- Panel Installation 23 23
- Framed Panels 23
- (6) to a maximum of 25
- 8" (16) 26
- (6) to a maximum of 1 27
- (29). If the panel 27
- (6) or thinner, you will 27
- 2" (13) 29
- Panel Installation 31 31
- Flush Inset Panels 31
- Panel Offsets Illus 34
- IMPORTANT NOTE: S 35
- IMPORTANT NOTE: T 35
- Dual Installation 36 36
- Dual Installation 36
- (2108) finished height 37
- Service Information 39 39
- Service Information 39
- Installation Checklist 39
- 7021793 REV-A 9/2011 40
Prodotti e manuali riguardandi no Wolf 600 Series BI-48SD
no Wolf Sub-Zero 648PROG Manuale Utente
(12 pagine)
(12 pagine)
no Wolf ICBDD30 Guida di Installazione
(8 pagine)
(8 pagine)
no Wolf Sub-Zero 700TF Guida di Installazione
(20 pagine)
(20 pagine)
no Wolf VRR 36 Manuale Utente
(1 pagine)
(1 pagine)
no Wolf 650G Specifiche
(80 pagine)
(80 pagine)
no Wolf ICBDD30 Manuale Utente
(74 pagine)
(74 pagine)
no Wolf Sub-Zero 648PROG Guida di Installazione
(20 pagine)
(20 pagine)
no Wolf Sub-Zero UC-24R Guida di Installazione
(16 pagine)
(16 pagine)
no Wolf 600 Series BI-48S Manuale Utente
(13 pagine)
(13 pagine)
no Wolf W482210 Manuale Utente
(2 pagine)
(2 pagine)
no Wolf PL582212 Manuale Utente
(2 pagine)
(2 pagine)
no Wolf 685 Manuale Utente
(1 pagine)
(1 pagine)
no Wolf 811504 Manuale Utente
(270 pagine)
(270 pagine)
no Wolf ICBCT30IU Manuale Utente
(100 pagine)
(100 pagine)
no Wolf FHBO Manuale Utente
(8 pagine)
(8 pagine)
no Wolf CT15G/S Manuale Utente
(2 pagine)
(2 pagine)
no Wolf Steamer Manuale Utente
(59 pagine)
(59 pagine)
no Wolf Multi-Function Cooktop Manuale Utente
(63 pagine)
(63 pagine)
Samsung HT-D400 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Odtwarzacze DVD Samsung HT-D400.
Dostarczamy 1 pdf podręczników Samsung HT-D400 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale